Fluke                                                       MET/CAL Procedure
=============================================================================
INSTRUMENT:            Yokogawa uR1000: CAL ADJ
DATE:                  15-Sep-97
AUTHOR:                Fluke Corporation
REVISION:              $Revision: 1.5 $
ADJUSTMENT THRESHOLD:  70%
NUMBER OF TESTS:       1
NUMBER OF LINES:       93
=============================================================================
#
# Compatibility:
#   5500/CAL 4.0 or MET/CAL 4.0 or later.
#
# Subprocedures:
#   None
#
# Required Files:
#   None
#
# System Specifications:
#   TUR calculation is based on specification interval of the accuracy file.
#   The default 5520A accuracy file contains 90 day specs.
#
# Fluke makes no warranty, expressed or implied, as to the fitness
# or suitability of this procedure in the customer's application.
#
 STEP    FSC    RANGE NOMINAL        TOLERANCE     MOD1        MOD2  3  4 CON
  1.001  ASK-                        P                            F        V
  1.002  ASK+           K                              X
  1.003  HEAD         PRELIMINARY INSTRUCTIONS
  1.004  DISP         Connect UUT to AC power and turn unit ON.
  1.004  DISP
  1.004  DISP         Warm-up time: 30min - REQUIRED
  1.004  DISP         Temperature: 23 +/-2 degC
  1.004  DISP         Humidity: 55 +/-10%
  1.005  DISP         [32]                WARNING
  1.005  DISP         HIGH VOLTAGE is used or exposed during the performance
  1.005  DISP         of this calibration.  DEATH ON CONTACT may result if
  1.005  DISP         personnel fail to observe safety precautions.
  1.006  HEAD         ZERO PEN
  1.007  DISP         Enter the SET UP mode by turning the AC POWER OFF,
  1.007  DISP         press and HOLD the <ENT> key, turn the AC POWER ON
  1.007  DISP         hold key until the SET UP display appears.
  1.008  DISP         Use the UP/DOWN keys to select the display
  1.008  DISP         'SETUP=P ADJ', and press the <ENT> key.
  1.009  DISP         Use the UP/DOWN keys to select the display
  1.009  DISP         'P ADJ=ZERO', and press the <ENT> key.
  1.009  DISP
  1.009  DISP         Select the channel #(=pen number) which you want to
  1.009  DISP         adjust, then press the <ENT> key.
  1.010  DISP         Adjust value so the recording position is 0 +/-.2mm.
  1.010  DISP
  1.010  DISP         Changing the numeric value by 1 will result in a pen
  1.010  DISP         movement of .02mm. The pen moves AFTER pressing <ENT>.
  1.010  DISP
  1.010  DISP         Repeat procedure until pen is at 0 on the chart grid.
  1.011  DISP         The display ZERO SET will appear.
  1.011  DISP
  1.011  DISP         Then press the <ESC> key.
  1.011  DISP
  1.011  DISP         Repeat procedure for any other channel that needs adj.
  1.012  OPBR         Do you wish instructions for adjusting another channel?
  1.013  JMPT         1.008

  1.014  HEAD         FULL SPAN PEN
  1.015  DISP         Use the UP/DOWN keys to select the display
  1.015  DISP         'SETUP=P ADJ', and press the <ENT> key.
  1.015  DISP         Use the UP/DOWN keys to select the display
  1.015  DISP         'P ADJ=FULL', and press the <ENT> key.
  1.015  DISP
  1.015  DISP         Select the channel #(=pen number) which you want to
  1.015  DISP         adjust, then press the <ENT> key.
  1.016  DISP         Adjust value so the recording position is 100 +/-.2mm.
  1.016  DISP
  1.016  DISP         Changing the numeric value by 1 will result in a pen
  1.016  DISP         movement of .02mm. The pen moves AFTER pressing <ENT>.
  1.016  DISP
  1.016  DISP         Repeat procedure until pen is at 100 on the chart grid.
  1.017  DISP         The display FULL SET will appear.
  1.017  DISP
  1.017  DISP         Then press the <ESC> key.
  1.017  DISP
  1.017  DISP         Repeat procedure for any other channel that needs adj.
  1.018  OPBR         Would you like instructions again for another channel?
  1.019  JMPT         1.015
  1.020  DISP         Select the 'SETUP=END' display using the UP/DOWN
  1.020  DISP         keys, and press the <ENT> key.
  1.020  DISP
  1.020  DISP         Select the 'END=STORE' display and press <ENT> key.
  1.021  DISP         After several seconds, the unit will store the
  1.021  DISP         settings and return to normal operation.
  1.022  END